last weekends purchase.

Kolat · 02-22-2009, 07:32 PM

So I did'nt post any pics of this since it was'nt very pretty when I got it. Wood had lots of chips in the varnish and the colour of the wood was bleached and you could see where someone had put a slip over recoil pad on it and that left the wood 2 different colours. So I sanded it down and stained it. The wood did'nt really take the stain uniformly but I think it looks better than it did.

Before:

After:

T

Mic · 02-22-2009, 07:38 PM

your redneck workbench does not look very sturdy, nor strong... :p

Looks good though! You could try doing a light sand on it again, and going with a lighter color to bring out the grain in some area's, then seal it up.

Metonymy · 02-22-2009, 08:53 PM

I'd have gone with a much darker stain. I've always wanted a black walnut colored rifle.

Too bad I'm not willing to sand/stain my 10/22... lol

Kolat · 02-22-2009, 08:57 PM

that was using dark walnut stain.

Wood did'nt take the stain nearly as well as I hoped it would.

T

Mrwyld · 02-22-2009, 09:05 PM

looks good for a basic run over with sanding and staining.

Coug91 · 02-22-2009, 10:28 PM

Looks good!

JohnnyB · 02-23-2009, 04:40 PM

Love the workbench!

phishisgroovin · 03-06-2009, 06:27 PM

i use my wifes favorite household utility as my bench.

Kolat · 03-07-2009, 03:21 PM

Got a bushnell 6-18x50 for it and some leupold rings since the old ones were about 2mm too low for the new scope but the low mount leupolds were high enough.

T

Jared535 · 03-26-2009, 08:13 PM

what model is it Tiernan?

Kolat · 03-26-2009, 09:57 PM

remington 788.

T

02-22-2009, 07:32 PM	#1
Kolat Marksman Joined: Jan 2009 From: Spokane Posts: 371	last weekends purchase. So I did'nt post any pics of this since it was'nt very pretty when I got it. Wood had lots of chips in the varnish and the colour of the wood was bleached and you could see where someone had put a slip over recoil pad on it and that left the wood 2 different colours. So I sanded it down and stained it. The wood did'nt really take the stain uniformly but I think it looks better than it did. Before: After: T

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-22-2009, 07:38 PM	#2
Mic Rifleman Joined: Jan 2009 From: Wa Posts: 165	your redneck workbench does not look very sturdy, nor strong... :p Looks good though! You could try doing a light sand on it again, and going with a lighter color to bring out the grain in some area's, then seal it up.

02-22-2009, 08:53 PM	#3
Metonymy Marksman Joined: Jan 2009 From: Washington Posts: 370	I'd have gone with a much darker stain. I've always wanted a black walnut colored rifle. Too bad I'm not willing to sand/stain my 10/22... lol

02-22-2009, 08:57 PM	#4
Kolat Marksman Joined: Jan 2009 From: Spokane Posts: 371	that was using dark walnut stain. Wood did'nt take the stain nearly as well as I hoped it would. T

02-22-2009, 09:05 PM	#5
Mrwyld Gunslinger Joined: Feb 2009 From: Everett, WA Posts: 94	looks good for a basic run over with sanding and staining.

02-22-2009, 10:28 PM	#6
Coug91 Rifleman Joined: Jan 2009 From: Spokane Posts: 223	Looks good!

02-23-2009, 04:40 PM	#7
JohnnyB Gunslinger Joined: Feb 2009 From: Oregon Posts: 52	Love the workbench!

03-06-2009, 06:27 PM	#8
phishisgroovin Gunslinger Joined: Mar 2009 From: Kent Posts: 83	i use my wifes favorite household utility as my bench.

03-07-2009, 03:21 PM	#9
Kolat Marksman Joined: Jan 2009 From: Spokane Posts: 371	Got a bushnell 6-18x50 for it and some leupold rings since the old ones were about 2mm too low for the new scope but the low mount leupolds were high enough. T

03-26-2009, 08:13 PM	#10
Jared535 Rifleman Joined: Mar 2009 From: Spokane Posts: 106	what model is it Tiernan?

03-26-2009, 09:57 PM	#11
Kolat Marksman Joined: Jan 2009 From: Spokane Posts: 371	remington 788. T